How to revive a dead 12v battery – The Ultimate Guide to Restoring Batteries

How to revive a dead 12v batteryIf you are having a battery which is old in your cars and truck and has a voltage which is low, it could be time that you have to start a project for restoring it. Bring back a vehicle battery is very important as it saves your loan and time.

The batteries of a vehicle are lead batteries which just means that these batteries are having lead-acid cores hence they can suffer from sulfation as times passes. Sulfation is when there is sulfur which has actually accrued on lead plates in the battery’s housing. When the amount of sulfur rust is not excessive, one can choose to restore the battery.

When restoring your battery, you will need baking soda, power drill, Epsom salt, storage container which is non-metallic, a storage funnel which is not metallic, safety glasses, replacement plugs which are made of plastic, wrench, gloves, water, battery charger for the lead acid batteries and distilled water.

How to revive a dead 12v battery
• Shut off your automobile and make sure that the battery cools off for around one hour.
• Open vehicle hood then utilize the wrench in detaching your cable television for negative battery then followed by positive cable.

Guarantee that you do not touch the wrench with any other part which is metal in order to make sure that you do not have an electrical power shock.How to revive a dead 12v battery

• Remove your battery from where it is placed in the car. Get rid of the cell caps which are made from plastic which are on the upper part of the battery. Find the sealed cells location with the power drill that you have. Use your work gloves then turn this battery upside down on a storage which is metallic in order to drain this fluid which is within. How to revive a dead 12v battery

• Put baking soda in this battery fluid in little increments using a tablespoon which is meant to neutralize it. When bubbling drop in this fluid, firmly close this container then dispose it. ezbattery reconditioning

• Take Epsom salt then stir among its part in three parts pure water that is warm till you have a quart of the magnesium sulfate solution. Insert the non-metallic funnel in the open battery cells then put this solution in the battery cells. How to revive a dead 12v battery

• Clip the negative and the positive terminals on their respective terminals. Let the charger dial to 12 volts then turn the battery charger on. The trickle should charge for 12 hours prior to you turn it off or unclipping the leads from the terminals.
• Return the caps and utilize plastic plugs for them to cover the holes that have been drilled
After this treatment you will have restored your battery successfully.

THE BEST WAYS TO RECONDITION A BATTERY

How to revive a dead 12v battery
When a battery gets old, some individuals think that it is expected to be tossed but that is not the case. It is possible recondition a battery and have it operating 100%. It is a procedure which is simple and anyone can do it. Just a few devices and some products for one to get a battery which is totally brand-new.

The elements that are required for reconditioning are voltmeter, distilled water, syringe and a battery charger.

How to revive a dead 12v battery
• One is then needed to remove the battery’s rubber which is utilized to protect the cap. Guarantee that you eliminate all the caps where some batteries have up to 7 caps. ez battery reconditioning

How to revive a dead 12v battery
• Fill the battery with distilled water then charge it for one hour up until you start seeing bubbles in the holes. While undertaking this treatment guarantee that you have not returned the caps. If you do not see the bubbles, reverse favorable and negative wires then await 2 minutes. After you see the bubbles return the wires in their ideal positions then charge the battery again for an additional half an hour.
• Replace the acid which is inside the battery with an acid which is brand-new with pure water then guarantee that you charge this battery for some few hours.
In the case of a laptop computer battery you will be needed to follow the following treatment;
• Remove the battery from your laptop and location it in a plastic bag.
• Place this plastic bag that has the battery in it in a freezer then await twelve hours. Remove it from the plastic bag then tidy it.
• Return it to the laptop computer then charge it up until it is full.
If your battery is not dripping then it does not have acid around it. This treatment is cheaper and easier for this reason you will wind up the costs on a brand-new battery There are laptop computers that will need to be “reset” for them to have a battery life that is much better.

Here you will charge your battery to 100% then leave it for 2-3 hours. Leave the laptop computer while it is unplugged and await the battery to be completely empty and leave it for 5 hours in this state. Recharge the laptop once again until it gets to 100%. This is a solution that is understood to increase the life of a battery. How to revive a dead 12v battery
These are basic ways that one can carry out in order to bring back the life of your battery. How to revive a dead 12v battery

richard